The Blink Camera Flashes Red 6 Times means that the batteries of the device are falling. Make sure you have installed two new AA 1.5-volt lithium non-rechargeable batteries.
If the red light on the camera stops flashing, it means the batteries are completely dead.
If the internet is down, the pattern of red flashing lights will be different. It will continuously flash short and fast. Before it stops, the red light of the Blink camera will blink a few times.
It is very important to keep a regular check on battery usage. It is because you can change them before they die completely.
All batteries have a lifespan. If you will note down the time, you will have a reminder to replace it.
Make sure you are using approved, AA lithium non-rechargeable batteries.
Why Blink Camera Flashes Red 6 Times?
If Blink Camera 6 Red Flashes, either your camera has not been connected to the internet or the battery of the device is too low. So, make sure that the internet connection is working perfectly.
No internet connection or damaged batteries might be responsible for the Blink Camera Not Recording Motion. In case, you will see the red light in Blink Mini, it simply means the device has not been connected to the internet.
During the Blink Camera Setup, you will see Blink Camera Red Light until the setup will not be completed. Once the process is completed, the light will change to green.
There might be various reasons why Blink Camera Flashes Red 6 Times. Let’s move further and find out the reason why.
§ Blink Camera Setup
If you haven’t configured the Blink Outdoor Camera yet, the red light on the Blink camera is a sign of the setup process.
The Blink Camera Flashing Red during the setup for a while and then it will be replaced by green light followed by a solid blue light. It simply means that the setup of the device has been completed successfully.
§ Internet Issue
When Blink Camera Not Recording Sometimes and shows red flashing times, it means your camera is not connected to the internet due to any glitch.
Or else, the sync module has been placed too far from the router.
First, minimize the distance between the sync module and the router. Check if the Blink camera has started recording or is still Blink Camera Not Working Flashes Red Light 6 times.
You can check the internet connection by connecting any other device with the same network. If the mobile network is working fine, it means something is wrong with the Blink camera. If the internet is still not connected to any other device, contact your service providers.
§ Blink Camera Is Detecting Motion
There are a number of Blink security cameras that show Blink Camera Flashes Red 6 Times at the time of detecting motion.
If the red light is disturbing you, make changes in the settings.
What Does It Mean When A Blink Camera Flashes Red?
Your Blink camera might be trying to connect to the internet. This is why Blink Camera Sync Module Red Light is flashing. Without a good speed internet connection, the Blink camera will not record anything.
Above, we have discussed all the possibilities when Blink cameras start flashing red lights.
It could be a bad internet connection, damaged camera batteries, or else you are doing a Blink security camera setup.
Are Blink Camera Motion Activated?
Blink cameras have built-in motion sensors that will make you alert while detecting motion. You can change the setting of the motion detection based on your preference. If you will set the motion detection to low, the motion even activates with a slight movement. On the other hand, if you set it too high, it will not capture motion that you can see with the naked eye. Hence, we suggest you set it to Mid.
How Do I Reset My Blink Camera?
If your Blink Camera is Unresponsive or Blink Camera Not Working, resetting the device is the last option to troubleshoot.
In this guide, we have talked about why Blink Camera Flashes Red 6 Times. If you have followed the step but still facing the same issue then reset the device following the below-given steps:
- There is a reset button given at the back of the Blink security camera
- You can use the button to put the sync module into the setup mode or reset the device too.
- When you will press the reset button, it will offline your Blink camera
- Once reset, you need to reconfigure the sync module again.
1. Power Recycle the Sync Module First
If you are facing some issues with your sync module, it is best to power recycle the sync module. Remove the power cord from the back of the module for at least 10 seconds. Plug in the cord again.
In a short time, the device will be rebooted and reconnected. It will then show you a solid blue and green light or solid blue and blinking green when the device is ready to set up.
2. Press the Reset Button For 5 Seconds
If power recycling the device doesn’t work, reset the device using a thin pin-like object. After pressing the button, you will see a flash of red light. After 15 seconds, the blinking blue light and solid green light will appear at the front of the Sync Module.
Check if the issue is resolved or still Blink Camera Not Responding.
Conclusion
In the guide, we have discussed how to fix when Blink Camera Flashes Red 6 Times. If you have applied all the given steps but are still facing the same issue, you should contact Blink support. Our experts will resolve the issue in a short time span.